Current Sensors · PCB Mount · 5-pin primary

EMK Series

Name: EMK
Brand: ADISENS

Precision open-loop Hall-effect current sensing for compact power electronics.

The EMK Series uses a high-sensitivity programmable Hall IC with factory digital calibration and compensation. It measures DC, AC and pulsed current with galvanic isolation, a 2.5 V centred analog output and support for 1, 2 or 3 primary turns.

15–75 ANominal current range

Up to ±225 AMeasuring range

4 kV ACDielectric strength

<2 µsTypical response

250 kHzBandwidth @ −3 dB

5-pin primaryPrimary topology

ADISENS EMK series board-mount current sensor

References & Documents

EMK technical characteristics and datasheets

Each reference below links directly to its controlled ADISENS technical datasheet.

Reference	Product code	Nominal current	Measuring range	Sensitivity	Supply	Output @ 0 A	Linearity	Accuracy @25°C	Response	Bandwidth	Isolation	Datasheet
EMK-15CP5Available on request	10800015031300001	15 A	±45 A	41.67 mV/A	4.75–5.25 V	2.5 V typ.	0.3% IPN typ.	±1% IPN	<2 µs	250 kHz	4 kV AC	Open PDF ↗Available on request
EMK-25CP5Available on request	10800025031300001	25 A	±75 A	25 mV/A	4.75–5.25 V	2.5 V typ.	0.3% IPN typ.	±1% IPN	<2 µs	250 kHz	4 kV AC	Open PDF ↗Available on request
EMK-50CP5Available on request	10800050031300001	50 A	±150 A	12.5 mV/A	4.75–5.25 V	2.5 V typ.	0.3% IPN typ.	±1% IPN	<2 µs	250 kHz	4 kV AC	Open PDF ↗Available on request
EMK-75CP5Available on request	10800075031300001	75 A	±225 A	8.33 mV/A	4.75–5.25 V	2.5 V typ.	0.3% IPN typ.	±1% IPN	<2 µs	250 kHz	4 kV AC	Open PDF ↗Available on request

PCB integration

EMK: 5-pin primary architecture

The package is designed for direct through-hole integration of the primary conductor and secondary signal pins.

10.2 mmPrimary conductor pin pitch

2.54 mmSecondary signal pin pitch

8.5 mmElectrical clearance on PCB with recommended layout

9.5 mmPackage clearance / creepage

13 gTypical sensor mass

1–5 IN · 6–10 OUTPrimary IN / OUT terminal definition

Signal architecture

5 V analog measurement interface

VREF2.5 V typical reference output

VOUTAnalog output: VOUT = VOFF + Gth × IP

GNDSupply and signal ground

VCCPositive supply voltage, +5 V ±5%

Np = 1 / 2 / 3Selectable primary turns for effective range scaling

RL = 10 kΩReference load condition used for specified performance

Applications

Optimised for compact power-conversion electronics

AC Variable-Speed DrivesFast phase-current feedback for motor control. Servo Motor DrivesHigh-bandwidth isolated current feedback. Photovoltaic InvertersDC/AC converter stages and current-loop monitoring. Battery ApplicationsCompact isolated current sensing in battery-fed power systems. SMPS & UPSFast current measurement in switch-mode power supplies. Welding Power SuppliesPulsed-current measurement and converter protection.

Standards & Compliance

Electrical-safety and environmental integration

IEC 61010-1Electrical safety framework for measurement and control equipment.

EN 50178Electronic equipment for use in power installations.

UL94-V0Housing material flammability classification.

CE / RoHS / REACHConformity and environmental declarations available from ADISENS.

Back to the family

Compare EM, EMT and EMK

Return to the family page to compare the three primary-conductor arrangements and available current ratings.

EM / EMT / EMK Family →

Custom engineering

Need a project-specific configuration?

Share your current range, PCB constraints, available conductor routing and required dynamic performance.

Request a Custom EMK →